17. File Extraction¶
The file extraction code works on top of selected protocol parsers (see supported protocols below). The application layer parsers run on top of the stream reassembly engine and the UDP flow tracking.
In case of HTTP, the parser takes care of dechunking and unzipping the request and/or response data if necessary.
This means that settings in the stream engine, reassembly engine and the application layer parsers all affect the workings of the file extraction.
The rule language controls which files are extracted and stored on disk.
Supported protocols are:
stream.checksum_validation controls whether or not the stream engine rejects packets with invalid checksums. A good idea normally, but the network interface performs checksum offloading a lot of packets may seem to be broken. This setting is enabled by default, and can be disabled by setting to “no”. Note that the checksum handling can be controlled per interface, see “checksum_checks” in example configuration.
file-store.stream-depth controls how far into a stream reassembly is done. Beyond this value no reassembly will be done. This means that after this value the HTTP session will no longer be tracked. By default a setting of 1 Megabyte is used. 0 sets it to unlimited. If set to no, it is disabled and stream.reassembly.depth is considered. Non-zero values must be greater than
stream.stream-depth to be used.
libhtp.default-config.request-body-limit / libhtp.server-config.<config>.request-body-limit controls how much of the HTTP request body is tracked for inspection by the http_client_body keyword, but also used to limit file inspection. A value of 0 means unlimited.
libhtp.default-config.response-body-limit / libhtp.server-config.<config>.response-body-limit is like the request body limit, only it applies to the HTTP response body.
17.3.1. File-Store and Eve Fileinfo¶
There are two output modules for logging information about extracted files.
The first is
eve.files which is an
fileinfo records. These
fileinfo records provide
metadata about the file, but not the actual file contents.
This must be enabled in the
- outputs: - eve-log: types: - files: force-magic: no force-hash: [md5,sha256]
See Eve (Extensible Event Format) for more details on working with the eve output.
The other output module,
file-store stores the actual files to
file-store module uses its own log directory (default: filestore in
the default logging directory) and logs files using the SHA256 of the
contents as the filename. Each file is then placed in a directory
named 00 to ff where the directory shares the first 2 characters
of the filename. For example, if the SHA256 hex string of an extracted
file starts with “f9bc6d…” the file we be placed in the directory
The size of a file that can be stored depends on
if this value is reached a file can be truncated and might not be stored completely.
If not enabled,
stream.reassembly.depth will be considered.
file-store.stream-depth to 0 permits store of the entire file;
here, 0 means “unlimited.”
file-store.stream-depth will always override
when filestore keyword is used. However, it is not possible to set
to a value less than
stream.reassembly.depth. Values less than this amount are ignored
and a warning message will be displayed.
A protocol parser, like modbus, could permit to set a different
store-depth value and use it rather than
Using the SHA256 for file names allows for automatic de-duplication of extracted files. However, the timestamp of a pre-existing file will be updated if the same files is extracted again, similar to the touch command.
fileinfo record can be written to its own file
sharing the same SHA256 as the file it references. To handle recording
the metadata of each occurrence of an extracted file, these filenames
include some extra fields to ensure uniqueness. Currently the format
<SECONDS> is the seconds from the packet that triggered the
stored file to be closed and
<ID> is a unique ID for the runtime
of the Suricata instance. These values should not be depended on, and
are simply used to ensure uniqueness.
fileinfo records are identical to the
logged to the
See File-store (File Extraction) for more information on configuring the file-store output.
This section documents version 2 of the
file-store. Version 1 of the file-store has been removed as of Suricata version 6.
Without rules in place no extraction will happen. The simplest rule would be:
alert http any any -> any any (msg:"FILE store all"; filestore; sid:1; rev:1;)
This will simply store all files to disk.
Want to store all files with a pdf extension?
alert http any any -> any any (msg:"FILE PDF file claimed"; fileext:"pdf"; filestore; sid:2; rev:1;)
Or rather all actual pdf files?
alert http any any -> any any (msg:"FILE pdf detected"; filemagic:"PDF document"; filestore; sid:3; rev:1;)
Or rather only store files from black list checksum md5 ?
alert http any any -> any any (msg:"Black list checksum match and extract MD5"; filemd5:fileextraction-chksum.list; filestore; sid:4; rev:1;)
Or only store files from black list checksum sha1 ?
alert http any any -> any any (msg:"Black list checksum match and extract SHA1"; filesha1:fileextraction-chksum.list; filestore; sid:5; rev:1;)
Or finally store files from black list checksum sha256 ?
- alert http any any -> any any (msg:”Black list checksum match and extract SHA256”; filesha256:fileextraction-chksum.list; filestore; sid:6; rev:1;)
Bundled with the Suricata download, is a file with more example rules. In the archive, go to the rules directory and check the
Suricata can calculate MD5 checksums of files on the fly and log them. See Storing MD5s checksums for an explanation on how to enable this.